Wind-Power Generator

How to build a residential-sized wind-turbine!

I produced this video while attending a course at Clackamas Community College.  As a class, we set out to construct two wind-turbines.  One with 3′ blades and the other with 6′ blades.

… I dropped the ball on this one!  I do not have a parts/tools list.  But, I can say it was the instructors goal to use as little manufactured parts as possible.  The radial bearing and rare-earth magnets are obvious exceptions.

Caution: Rotor becomes dangerous once the magnets are attached.  One wrong move could have easily broken someones arm!

 

 

 

Rather start with something smaller that has a clear set of directions?!  I don’t blame you.  Try this Mini-Wind Turbine from the Pembina Institute.

..or, you may want to try another form of power generation.

[ Readmore. ]

Hydro-Power Generation

DIY Hydro-Generator

This was a project in partnership with classmate Ryan Denham.  We set out to build a three-phase mini-hydro-electric generator from average easy-to-find materials.  And, this is how we did it..

Tools List:

  1. Saws
  2. Hacksaw
  3. Jigsaw
  4. Miter saw
  5. Table saw or Skill saw
  6. Drill Bits
    1. 1/4”
    2. 1/2”
    3. 1 & 1/8” Spade Bit
  7. Glue Gun
  8. Measuring Tape
  9. Straight Edge
  10. Quick Square
  11. Clams
  12. Wrench
  13. Soldering Iron
  14. Volt-meter

 

Parts List:

  1. 28 AWG Enameled Magnet Wire
  2. Electrical Tape (Blue, Green, Red)
  3. Hot Glue Sticks
  4. Two Pieces of Ply Wood (12” x 13”) wide and (3/8”) thick
  5. Two Circular Bearings (1/4” inner diameter and 1 & 1/8” outer diameter)
  6. 1/2” Solid Metal Bar
  7. *Epoxy or Alternative Chemical Binder
  8. One (12” x 12”) piece of light wood (3/8”) thick
  9. 12 – 24 Large Washers
  10. 12 – 24 Large Neodymium Magnets
  11. Handles
  12. 4 Bolts (6” x  1/4″) with 12 nuts
  13. Two 1/2” Inch slices of PVC
  14. Sandpaper
  15. Compass
  16. 12+” Diameter Fan Blades
  •  Use Fan Blade style for high velocity (low head)
  • Use Pelton Wheel for high pressure (high head)

NOTE:  Pressure = (Water Density)(acceleration of gravity)(height)


 

 

Step 1)   Build Stators

  1. Cut Both [pieces of plywood into (12” x 13”) rectangles
  2. Place tape 5/16” from tip of 1 & 1/8” spade bit
  • Drill 5/16” into inside center of both pieces of plywood
  1. Clamp both pieces of plywood together in alignment with 12” square of light wood
  2. Drill through center of all three pieces of wood at once with 1/2” drill bit
  3. Drill into four corners using 1/4” drill bit
  • Draw 12” diameter circle around the hole just drilled on all pieces of wood.
  • Secure circular bearings into insets drilled into inside center

 

Step 2)   Wrap Coils

  1. Wrap magnet wire into a coil with 200 turns and approximately an inch in diameter
  2. Tape coil on both sides using colored electrical tape
  • Using the same continuous strand of wire, repeat 3 more times.
  1. Using different colors make two more sets of coils. [Four Coils per Set]
  2. Repeat entire coiling process if both sides of rotor are to be utilized for power production
  3. Use hot-glue to secure coils around 12” circle made around center of stator
  • Wire in three-phase [Diagram]

 

Step 3) Build Rotor

  1. Cut 12” diameter circle around lightwood using Jigsaw
  2. Secure solid metal rod into center 1/4” hole drilled in step 1
  • Glue 12 large washers evenly around the circumference, repeat on other side if both sides of rotor are to be utilized
  1. Carefully place magnets onto washers, alternating polarity [Hint: compass may come in handy]

Step 4) Assemble

  1. Slide rotor rod into circular bearings of stators using PVC spacers sandwiched in-between.
  2. Place 6” screws into four corners of stators [place nuts on each side of stator]
  • Use voltmeter to test

 

*Bonus:  For major hydroelectric generators, we need to divert the fish around the dam.  A “fish sorting center” separates BIG FISH from small fish… and can sometimes be traumatic as shown below.

 


 

 

..or maybe you’d like to try your hand at another form of power generation.

[ Readmore. ]

Energy Workshop

This is the Energy Workshop!

I will be periodically uploading DIY projects (with how-to video) for others to examine/replicate/comment on/share.  There is no particular order.  Choose any subject that interests you.

I challenge you to improve upon my projects!  Send them back to me and i’ll update the design… and give you the credit.

Want to be a better circuit designer? Visit the ‘simulations laboratory‘ to learn new ways to test your ideas.

Note:  Please provide constructive feedback!  I am officially crowd-sourcing the improvement of my videos, website, and project ideas to all of you.  

 

Let’s get building!!

Analog:  *Power supplies, *Filters, *Electromagnetism

Digital: *Pulse Width Modulation, *Arduino, *User Interface

Electro-Chemical Storage: *Energy Storage, *Battery Chargers

Generation: Solar, Wind, Hydro

*No Projects Yet Available

[ Readmore. ]

Signal Simulation

The complexity of our designs will result primarily on our predictive power.

In-order for us to be sure of our designs, we must do two things:

  1. Construct a circuit using ideal components.  (think functionality)
  2. Replace ideal components with real world numbers.  (think efficiency/precision)

Note:  Step 2 is only necessary if we intend on physically creating a project.

Ready to make things happen?  Head over to the ‘Energy Workshop‘ to participate in energy-based projects.

 

 

Let’s get simulating!!

LT Spice:  *Circuit Design

ModelSim:  *Digital Signals, *VHDL coding

Labview:  *Data Acquisition, *Signal Generation, *Signal Analyzing

Matlab: *Statistics, *Physics, *Controls

*No Projects Yet Available

[ Readmore. ]